Some More Parts to Improve the Car...

In my quest to improve my IS-F in the most efficient manner possible, I have been slowly collecting some parts over the past year or so which I thought would bring me the best bang for the buck. Because I haven't been as good at updating this blog as my GT-R blog, I'm going to simply lay out all of these parts.

First -  I decided to replace the OEM halogen fog lights with later year (2011-2014?) OEM LED fog lights - just plug and play...

Before

Much whiter!

And yes my car wasn't clean when I took this photo...

As for performance of LED vs halogen, hard to say really. They are mounted so low and act only to fill in the dark space under the headlights so I think the effect is more of a visual, than performance difference. Oh well, wasn't that expensive and it gives a more modern look...

I had also learned from Yamada-san at CREF (where I had the clear film installed) that when Toyota was developing the IS-F, they found that the large amount of power meant that the rear subframe would actually move and cause some instability, and that this was especially noticeable on a rain slick track. So, Spoon Sports developed the Rigid Collar kit for the ISF.

Just a few collars...

For anyone not familiar with the Rigid Collar concept, here is a video link that describes how they work.

Yes it sounds too good to be true, but yes they work and I will go into more detail in a future post about what they did for my car's handling. I had gotten them for my GT-R and was suitably impressed so the lack of internet feedback on their use on the IS-F didn't bother me.

I had also read on the ClubLexus forum how the Apex'i throttle controller made the car feel much more responsive (but not necessarily faster - but that's ok, I just want something more responsive!). So, I ordered one and the car-specific harness.

From: https://www.clublexus.com/forums/is-f-2008-2014/626697-apexi-throttle-control-installed-i-love-it-d-2.html

In a later post, I'll discuss this part - all I will say for now is, it really is worth getting!

Finally, some bling - I found something in my closet that I had ordered when I first ordered the car, but was not delivered in time for the dealer to install it, a dry carbon fiber rear license plate frame from LEMS.

Two photos from their website (as I was too lazy to unwrap it before handing it Ninomiya-san to install):

Side facing out

Body side

Here is the rear license plate before:

... and now afterwards! 

As you can see in Japan, there is this metal "cap" on the upper left bolt that has to be installed by special tooling (available only at the DMV). So Ninomiya-san had to make a quick trip in order to get it done... but I think the results are worth it!

Now I have to decide whether to splurge on a matching dry carbon fiber FRONT license plate frame and/or a rear trunk lip spoiler...but before that, one more piece of (possibly functional?) bling... stay tuned!

New Bumper Cover... Part 2

Two days after I dropped off the car at the local Porsche shop CREF, I went to pick up the car.

That is one tasty 911 GT RS3....

As if not obvious by now, I had gone to this shop because they seem to be one of only a very few places in Japan that specialize in the application of protectant film for cars (they had a Bentley in the shop when I had arrived, and a Gallardo on the way...). Rather than anything from 3M, they use the Xpel line up, and in particular they used the latest self-healing type (Xpel Ultimate) for my car. Here is a video clip I found:

And here is a link to the nationwide association in Japan these guys at CREF actually head up.  I had gone ahead and ordered the full front bumper (of course), the door handle cups, the top of the rear bumper, and lastly, some custom work on the rear door entry areas (because of the kids). What's interesting is that, while the bumper of course is brand new, the other areas had some slight scuffs in the clearcoat - and yet as Ishiguro-san at CREF promised, once the film was applied those slight imperfections really can't be seen!

Yes, slight orange peel visible, but now I can fly on the expressway with no worries...
(the hood already has too many chips for me to care)

In any case, this being Japan the craftsmanship was, as usual, nearly perfect.

Door handle cups - all 4 done!

Upper bumper area which often gets scratched when loading stuff. You can see my finger pointing to the line

On the rear door entry areas, we originally were planning just a simple strip on the edge, but they went ahead and put down a whole lot more, just in case (and without changing the estimate!)

Arrow pointing to upper edge

Arrows show bottom edge and how it extends to the side.

Obviously several other areas of the car still need work - for example the hood needs to be repainted in places and the right rear quarter panel has some paint chips. But for now I'm happy with the additional protection.

I'm not done with CREF though... turns out they have 2 other key items I've been looking at getting done...

New Bumper Cover... Part 1

So, as the title says, one thing I had done at the Lexus dealer was to have the beat up original bumper cover, with all of its scratches and chips thanks to the previous owner, replaced with a brand new bumper cover from the factory. Being a Lexus factory part, the paint is absolutely perfect.

Beautiful!

But to stay absolutely perfect is not possible, not matter how much wax or sealant is applied, especially when the car is on the expressway often as it is in my case. But, I had, even before buying the car (but after seeing it), thought about getting certain parts of the car repainted so I had ordered several pieces of 3M clear protection film pre-cut for the ISF, from the US.

Here are the film cutouts for the bumper and mirrors.

On my GT-R, I had successfully cut my own templates, from which I cut headlight protection thickness 3M clear film, and then applied to the headlights. So, I figured that with lots of time and patience, application of the bumper piece on the ISF would be the same, especially because it was already pre-cut.

So, I took off the (required in Japan) license plate and its holder:

This must be the cheapest piece on the car. Will have to upgrade soon.

Those are some LARGE holes...

And then I washed the bumper and used a Zaino claybar to remove any dust, just in case:

After it was all clean, I sprayed the front bumper with the distilled water and baby shampoo mix:

The bumper film has yet to be peeled away and is sitting upside down on the hood

And then, as deftly as possible I removed the 3M film from its backing and tried to apply it to the bumper:

Was ok so far...

Finally got it on, somehow....

And then came the process of using the supplied squeegees to remove the activator fluid of distilled water and alcohol.

When I finished, however, I learned that 1) in getting the film to fit in some areas, I had overstretched the material so it would not fit in others, 2) despite my washing down the garage some dust had gotten trapped and caused some rough spots (redoing the application in places to remove this dust was driving me insane) and 3) some fluid just could not be removed.

What it looked like when I gave up...

Finally, after spending the entire afternoon doing this, as it began to get dark I decided to give up. The photo above was taken right before I walked away disgusted with myself.

The problem remained, however, what to do - could this be salvaged (I guess I could drive it around looking horrible until it was fixed) or was there another solution?

For the GT-R, I had also wanted to install some paint protection - I had bought a can of the 3M Paint Defender as well as a container of the Road Warrior Plus because I was concerned that I would not have the talent to cut bulk sheets of the 3M film to fit the GT-R.  But of course, for some reason I searched my garage and could find neither of these.

Finally I gave up, made some calls, and then found myself on Wednesday morning at a famous Porsche tuner in Yokohama, just 10 minutes away from where I live.

Stay tuned in Part 2 to see what I had done...